ORG. GND. 8-lead SOIC. 8-lead dBGA2. 8-lead PDIP. 8-lead SOIC. Rotated (R). ( 1K JEDEC Only). 8-lead mini-MAP (MLP 2×3). 8-lead TSSOP. DO. DI. NC. VCC. CS. SK. 1. 2. 3. 4. 8. 7. 6. 5. GND. Normal. Pinout. Rotated. Pinout .. 93C Address bits pattern -> User defined. Timing Diagrams. Address. 8-lead SOIC. 8-lead dBGA2. 8-lead PDIP. 8-lead SOIC. Rotated (R). (1K JEDEC Only). 8-lead Ultra Thin mini-MAP (MLP 2×3). 8-lead TSSOP.
|Published (Last):||8 December 2016|
|PDF File Size:||17.11 Mb|
|ePub File Size:||12.20 Mb|
|Price:||Free* [*Free Regsitration Required]|
Before years i tryed to read one rotated chip as normal, more than times and ofcourse i did’n read it, then i ask a friend and 93c466 say that maybe it is rotated and i tryed it like rotated and read it sucsessfull, so there was not problem. BeeHive8S discontinued Direct connection.
93C46 – Rochester Elect. | Elnec
If gnd on radio is on pin5 on pcb, so 93c4 is normal, if gnd is on pin7 on pcb, so chip is rotated. IT yes, they are: Blank A B C. Therefore we can return your samples only if we get chips from semiconductor manufacturer. MEMprog discontinued Direct connection.
93CX6 datasheet & applicatoin notes – Datasheet Archive
It was rotated, refitted it and radio now says error 3, so I think I have buggered it one way or the other, Still works if you hold down the band button and turn it on but it beeps all the time. PIKprog2 discontinued Direct connection. They are going up as well if you look at later listings by the same seller they are more expensive.
Device Search tip The names of 933c46 programmable devices in our database don’t contain all charactersshown at the top of the chip or mentioned in a datasheet section part numbering.
Pomona Electronics – http: The sample of programmable devices is necessary to have for test and release new chip support.
Reasonable quantity of this product can be available within 3 working days. Maybe it is rotated, did you check on what pin is gnd? I do not use it very often, now and every time I do I have to remove the token and then re-install the software.
Thanks Rotte, I think I will have to do that, sorry about your programmer, if it’s the one I think it is, there is only a handful of components on the board, cant you find out what’s faulty, or are you getting them replaced under warranty?
Thanks for the info on the 93c Read with a LV48 programmer. This number indicates quantity of items that could be produced from components in stock. Last time I tried rotatw would not re-install, and so I am sending it back for later software to be added.
If such code letter is at the end of the name, it should be omitted.
Yes I have had CDH gear for about 15 yearsthe first interface rptate had had a sine wave generator for doing the early Philips radio’s with ER The names of the chips in our database contain all characters necessary for identification of the device, but don’t contain such codes, that have no influence to the programming, for example temperature codespeed codepacking type codeetc.
MEMprog2 discontinued Direct connection.
Any help would be appreciated. Would I have damaged it if it was not rotated, and I read it as rotated. My CDH Electronics gear has thrown it’s teddy out of the pram again, and has to go back to see Colin, so I’m trying to read it with an Asix Presto, I wired it up as a rotated 93c46 and was unable to read, so tried as a normal one still the same.
MEMprogL discontinued Direct connection. In case of missed rottate, we always asking the semiconductor manufacturer for samples, but if samples are not available – also in the package you’re asking for the support – the solution from us will be delayed. Move the cursor over the box to highlight particular section.
T51prog2 discontinued Direct connection.